[PEDA] Many similar Sheet Symbols

[Phillip Stevens]

Hi Jakub,

It's too bad that AD6 isn't a possibility for you,  as a multi-channel design is
*much* easier with AD6.  Otherwise a lot of manual intervention is
required.  You might check out the multi-channel design demo's just to see
what AD6 could do for you in this area:
http://www.altium.com/webdemos/?p=10
http://www.altium.com/Evaluate/DEMOcenter/AltiumDesigneroverview/Multichanneldesign/

I don't recall 99SE auto-generating the sheets for you here,  I think you had to
copy/paste a sheet to make the new sheets.  Then manually edit all of the ref
des so there were no duplicates.

Somewhat painful in 99SE.  A piece of cake in AD.

---Phil Stevens

Wednesday, November 1, 2006, 8:22:19 AM, you wrote:

> Well, assume that AD6 is far away from horizon of my possibilities... :)

> I have put 20x Symbols to main schema and changed symbols' names and now
> the problem is to generate appropriate netlist and then user my pre-made
> PCB. Is that possible?


> Dennis Saputelli napisal(a):
>> GET AD6
>> :)
>> it really handles this pretty well
>>
>> in 99SE there are methods but at the end of the day i found that you 
>> really needed the 20 separate sheets
>> and getting them to all annotate nicely was a major pain
>>
>> the 'repeat' feature was what finally drove me to AD6
>>
>> Dennis Saputelli
>>
>>
>> _______________________________________________________________________
>> CONTACT INFORMATION:
>> _______________________________________________________________________
>> Integrated Controls, Inc.           Tel: 415-647-0480  EXT 107
>> 2851 21st Street                    Fax: 415-647-3003
>> San Francisco, CA 94110             www.integratedcontrolsinc.com
>> _______________________________________________________________________
>> NOTE! TO PASS OUR SPAM FILTER PUT THE FOLLOWING IN SUBJECT LINE: I.C.I.
>>
>>
>> Jakub M. wrote:
>>   
>>> [PROTEL 99 SE]
>>>
>>> In a device I want to put about 20 similar channels. Therefore I have 
>>> made a schema of a channel and have put it to main schema as a Sheet 
>>> Symbol 20 times. I have also made PCB for the single channel.
>>>
>>> Question:
>>>
>>> I want to generate netlist for the whole device and to use already made 
>>> PCB of channel (the same for all channels). How to do this?
>>>
>>>
>>> Regadrs,
>>> JM
>>>
>>>
>>>  
>>> ____________________________________________________________
>>> You are subscribed to the PEDA discussion forum
>>>
>>> To Post messages:
>>> mailto:PEDA at techservinc.com
>>>
>>> Unsubscribe and Other Options:
>>> http://techservinc.com/mailman/listinfo/peda_techservinc.com
>>>
>>> Browse or Search Old Archives (2001-2004):
>>> http://www.mail-archive.com/proteledaforum@techservinc.com
>>>  
>>> Browse or Search Current Archives (2004-Current):
>>> http://www.mail-archive.com/peda@techservinc.com
>>>
>>>
>>>     
>>
>>  
>> ____________________________________________________________
>> You are subscribed to the PEDA discussion forum
>>
>> To Post messages:
>> mailto:PEDA at techservinc.com
>>
>> Unsubscribe and Other Options:
>> http://techservinc.com/mailman/listinfo/peda_techservinc.com
>>
>> Browse or Search Old Archives (2001-2004):
>> http://www.mail-archive.com/proteledaforum@techservinc.com
>>  
>> Browse or Search Current Archives (2004-Current):
>> http://www.mail-archive.com/peda@techservinc.com
>>
>>
>>
>>   

>  
> ____________________________________________________________
> You are subscribed to the PEDA discussion forum

> To Post messages:
> mailto:PEDA at techservinc.com

> Unsubscribe and Other Options:
> http://techservinc.com/mailman/listinfo/peda_techservinc.com

> Browse or Search Old Archives (2001-2004):
> http://www.mail-archive.com/proteledaforum@techservinc.com
>  
> Browse or Search Current Archives (2004-Current):
> http://www.mail-archive.com/peda@techservinc.com